How To Reset Unifi Camera

Click for
Table of Contents

Package Contents

Pole-mounting: Two metal straps (non included)
Shielded Category 5 (or higher up) cabling with drain wire should be used for all outdoor wired Ethernet connections and should be grounded through the Air-conditioning footing of the PoE.
We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-class, shielded Ethernet cablevision from Ubiquiti. For more details, visit ui.com/toughcable
Surge protection should be used for all outdoor installations. We recommend that you use 2 Ethernet Surge Protectors, model ETH-SP, one near the photographic camera and the other at the entry point to the building. The ETH-SP will absorb ability surges and safely discharge them into the basis.

Ethernet Port
10/100/grand RJ45 port connects to an 802.3af/802.3at switch for PoE power and data.
Reset Push button
The Reset button serves two functions: Reboot Press and release the Reset push button quickly. Restore to Factory Defaults Press and concur the Reset push button for 10-20 seconds while the camera is powered on.
Cable Gland
Creates a tight seal effectually the Ethernet cable to prevent water from damaging the RJ-45 port.
LED Band
White	Ready for configuration.
Flashing White	Initializing.
Heartbeat Flashing White	Device is being reset to factory defaults.
Blue	Indicates the device has been successfully adopted into a network and is working properly.
Rotating Bluish	Motility detected.
Alternate White/Blue	Firmware upgrade in progress. Device is decorated; do not touch on or unplug it.
Repeating Off/White/Blueish	Recovery mode.
Flashing Cherry	Recording.
Scarlet	Device failure; network fault. If this occurs, we recommend rebooting the device.

Remove the sticker from the bottom of the Mounting Base of operations.

To install the camera, please follow the instructions of the following sections in this club:

The camera can be mounted on a wall, ceiling, or pole. Follow the appropriate steps for your installation:

	Important: If you are installing your camera outdoors, create a baste loop for the cablevision beneath the camera to prevent water ingress.

	IMPORTANT: For proper weather sealing, the Cable Gland must fit securely inside the Adjustable Base when the camera is mounted. Ensure that the Cablevision Gland is securely seated during installation and cablevision routing.

	Note: When y'all first launch UniFi Protect, the app will prompt you lot to enable Bluetooth and other features necessary to provide the all-time user experience possible. Please permit these features and permissions for proper app functionality.

UVC-G4-PRO
Dimensions	Ø 86 ten 153 mm (Ø 3.39 x vi.02") (Without Mounting Plate)
Weight	700 g (1.54 lb) (Without Mounting Plate)
Enclosure	PC/TPE/Aluminum Blend (ADC-12 + Liquid Coating)
Networking Interface	(1) 10/100/1000 Ethernet Port
Sensor	OS08A10, one/2"
Lens	F 4.1mm - 12.3mm; f/i.53 -f/3.3
LED	LED Ring
Field of View
Wide	108° (H), 58° (V), 125° (D)
Tele	37° (H), twenty° (V), 43° (D)
Night Fashion	IR LEDs with Mechanical IR Cut Filter
Video Compression	H.264
Resolution	4K2K (3840 x 2160)
Max. Frame Rate	30 FPS
Paradigm Settings	Flip, Brightness, Contrast, WDR, Hue, Infrared, Sharpness, Saturation, Denoise, fifty/lx Hz Flicker Reduction
Management Interface
Managed Mode	UniFi Protect
Standalone Mode	Camera Integrated Spider web UI
Microphone	Yep
Max. Ability Consumption	12.5W
Power Method	IEEE 802.3af/at
Ability Supply	802.3af/802.3at or UniFi PoE Switch
Buttons	Mill Reset Button
Mounting	Wall, Ceiling, Pole (Kits Included)
Operating Temperature	-twenty to fifty° C (-4 to 122° F)
Operating Humidity	0 to ninety% Noncondensing
Weatherproofing	IP67

Source: https://dl.ubnt.com/qsg/UVC-G4-PRO/UVC-G4-PRO_EN.html